Makale detayı · 2022
EFFECT OF PRINTING SPEED ON FDM 3D-PRINTED PLA SAMPLES PRODUCED USING DIFFERENT TWO PRINTERS
Dergi
International Journal of 3D Printing Technologies and Digital IndustryISSN 2602-3350
- Yıl
- 2022
- Tür
- article
Veri kaynağı ayrımı
- YÖKSİS YÖKSİS makale kaydı
- YÖKSİS dergi adı International Journal of 3D Printing Technologies and Digital Industry
- OpenAlex OpenAlex zenginleştirmesi (özet, atıf, konular)
Özet
OpenAlex · İngilizce
Today, 3D manufacturing technologies are shown as candidates to replace traditional manufacturing technologies. In this direction, many studies are carried out to reduce the disadvantages of 3D manufacturing technologies. The first few of these disadvantages are; high production cost, slow production speed, and lower strength values of the produced product compared to traditional methods. Increasing or decreasing the printing speed, which is one of the 3d production parameters, appears as a parameter that will directly affect the strength and production costs of the produced product. For this reason, it is important to determine the effects that may occur on the mechanical properties of the product produced by changing the printing speed in terms of choosing the printing speed according to the intended use of the product. In this study, the effect of desktop Fused Deposition Modelling (FDM) 3D printing speed on mechanical properties was investigated. Tensile test samples were produced using Polylactic Acid (PLA) material at seven different printing speeds using two different 3D printers operated without bed heating. The mass, hardness, surface roughness, and porosity values of the produced samples were determined. Fractured surfaces of the samples were analyzed using Scanning electron microscopy (SEM) images. The results show that an increase in the printing speed decreases the mass, the top surface hardness, and the tensile strength and increases the porosity, the arithmetic average roughness of the products produced with both 3D printers.
Konular
Atıflar
OpenAlex cited_by_count. WoS veya Scopus atıf sayısı değildir; o kaynaklar için ayrı kolon yoktur.
20 atıf
OpenAlex cited_by_count (önbellek / veritabanı)
Yerel katalogda bu makaleye atıf yapan 10 yayın (OpenAlex referans eşleşmesi; tam dünya listesi değildir).
- Optimizing printing parameters for enhanced mechanical properties of 3D printed PLA octet lattice structures 2023
- Investigation of The Effect of CNC Milling Cutting Process on The Tensile Test of PLA Samples Produced Using Two Different 3D Printers with The FDM Method 2024
- Investigation of The Effect of CNC Milling Cutting Process on The Tensile Test of PLA Samples Produced Using Two Different 3D Printers with The FDM Method 2024
- Investigation of Tensile Strength in 3D Printed PLA+ Samples: Influence of Raster Angle and Infill Density 2025
- The effect of cutting parameters in CNC milling on mechanical properties of 3D-printed polylactic acid tensile test samples: axis speed, cutting direction and number of cutting tool teeth 2025
- Farklı baskı açıları ve dolgu oranlarında üretilen polilaktik asit plakalarla birleştirilmiş yapıştırma bağlantılarının deneysel analizi 2024
- Farklı baskı açıları ve dolgu oranlarında üretilen polilaktik asit plakalarla birleştirilmiş yapıştırma bağlantılarının deneysel analizi 2024
- A comprehensive study on cellulose nanofibril reinforced polylactic acid 3D printed composites 2026
- 3B YAZICIDA ABS VE PLA MALZEME İLE ÜRETİLMİŞ LEVHALARLA OLUŞTURULAN TEK TESİRLİ YAPIŞTIRMA BAĞLANTILARININ ARAŞTIRILMASI 2024
- 3B YAZICIDA ABS VE PLA MALZEME İLE ÜRETİLMİŞ LEVHALARLA OLUŞTURULAN TEK TESİRLİ YAPIŞTIRMA BAĞLANTILARININ ARAŞTIRILMASI 2024