Makale detayı · 2024
A Study on the Optimization of Nano-B4C Content for the Best Wear and Corrosion Properties of the Al-Based Hybrid Nanocomposites
- Yıl
- 2024
- Tür
- article
Veri kaynağı ayrımı
- YÖKSİS YÖKSİS makale kaydı
- YÖKSİS dergi adı Arabian Journal for Science and Engineering
- Katalog eşleşmesi (ISSN) Arabian Journal for Science and Engineering
- OpenAlex OpenAlex zenginleştirmesi (özet, atıf, konular)
Özet
OpenAlex · İngilizce
Abstract This investigation is dedicated to producing hybrid nanocomposites based on AA2024, achieved through the utilization of powder metallurgy methods encompassing mechanical milling and hot pressing. The research focused on studying how changes in B 4 C content influence the mechanical, wear, and corrosion behavior of AA2024/h-BN/B 4 C hybrid nanocomposites. The findings revealed that as the B 4 C content increased, the relative density values decreased, and higher porosity values were observed in the hybrid nanocomposite samples. Among the tested samples, the hybrid nanocomposite with 4 wt% B 4 C exhibited the most favorable properties. It demonstrated significantly higher hardness and ultimate tensile strength compared to AA2024 matrix alloy, with values of 161 HB and 372 MPa, respectively. In contrast, the matrix alloy showed hardness and ultimate tensile strength values of 105 HB and 237 MPa, respectively. Furthermore, the wear resistance of hybrid nanocomposite with 4 wt% B 4 C displayed approximately 14 times greater wear resistance under 40 N load compared to the unreinforced AA2024 matrix alloy. The corrosion test results have revealed that the corrosion resistance of the hybrid nanocomposite reinforced with 4wt% B 4 C is nearly 47% higher compared to the corrosion resistance of the unreinforced AA2024 alloy. This nanocomposite exhibits the highest polarization resistance of 5.21 Ω.cm 2 .
Konular
Atıflar
OpenAlex cited_by_count. WoS veya Scopus atıf sayısı değildir; o kaynaklar için ayrı kolon yoktur.
46 atıf
OpenAlex cited_by_count (önbellek / veritabanı)
Yerel katalogda bu makaleye atıf yapan 31 yayın (OpenAlex referans eşleşmesi; tam dünya listesi değildir).
- Optimization of Dry Sliding Wear in Hot-Pressed Al/B4C Metal Matrix Composites Using Taguchi Method and ANN 2024
- Optimization of Dry Sliding Wear in Hot-Pressed Al/B4C Metal Matrix Composites Using Taguchi Method and ANN 2024
- Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal-metal composites 2024
- Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal-metal composites 2024
- Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal-metal composites 2024
- Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal-metal composites 2024
- Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal-metal composites 2024
- Effect of AlCrCuFeNi high entropy alloy reinforcements with and without B4C on powder characteristic, mechanical and wear properties of AA5083 metal-metal composites 2024
- Effect of mechanical milling time on powder characteristic, microstructure, and mechanical properties of AA2024/B4C/GNPs hybrid nanocomposites 2025
- Effect of mechanical milling time on powder characteristic, microstructure, and mechanical properties of AA2024/B4C/GNPs hybrid nanocomposites 2025